Stacking Pocket Corridor Nosing Clear Width Check
Quick answer: corridor nosing
A stacking pocket corridor nosing clear width check belongs at the drawing stage, before finishes and door frames are fixed. Where a top-hung movable wall parks beside a circulation route, the junction between the pocket opening, the corridor edge and the nosing detail decides how the space reads in daily use. This guide sets out a coordination framework for contractors, architects, interior designers and owners. The suitability of each route and parking arrangement depends on the approved layout, circulation, ceiling interfaces and operating sequence.
Why the Pocket-to-Nosing Junction Deserves Its Own Check
Movable wall panels are individually movable and suspended from a top track. They cross the opening without a floor track and park at a planned stacking position. That clear-floor principle is the reason the pocket area matters: the floor stays free along the partition line, so the visible edge of the corridor becomes a design and circulation decision rather than a hardware detail.
A corridor nosing is the finished edge where the floor surface meets a change in level, a threshold zone or the pocket recess. When the pocket sits at the end of a corridor, the nosing line and the parked panel line compete for the same few hundred millimetres of plan. Resolve that competition on paper, not on site.
What the Clear Width Check Actually Reviews
The check is a drawing review, not a single measurement. It asks whether the route people use when panels are open, closed or parked remains legible and unobstructed, and whether the pocket mouth is wide enough to receive the panels without forcing the corridor to bend around them.
Three conditions to review separately
- Panels closed: the partition line is complete and the corridor runs past a solid wall face.
- Panels in transit: panels travel along the overhead route between the opening and the pocket.
- Panels parked: the stack occupies its planned position and the corridor narrows at the nosing.
Each condition can produce a different pinch point. A layout that works when the room is closed may fail when the stack is full, because the parked panels and the nosing detail meet in the same zone.
Route Logic: Straight, Turning and Stacking Paths
Straight, turning and stacking routes are reviewed from the layout. A pocket placed on the corridor axis produces a straight stacking route but concentrates the stack at the busiest point. A pocket set to one side may keep the corridor cleaner but introduce a turn that needs its own clearance review.
Every proposed movement path requires a continuous connected overhead route and project-specific support review. The exact route, junction arrangement, continuous overhead path and parking position must be confirmed from the coordinated project drawings.
Evidence note: the product facts confirm top-hung movement, clear floors along the partition line and customized parking. They do not confirm dimensions, loads, support positions or accessibility compliance for any specific junction. Those items require the project drawings and the responsible design team.
A Step-by-Step Coordination Sequence
- Fix the room programme first. Confirm how often the space opens and closes, and which side of the corridor users approach from.
- Draw the parked stack at full extent. Show the planned stacking position as an occupied zone, not a dashed intention.
- Overlay the corridor nosing line. Mark the finished floor edge, any threshold zone and the pocket mouth on the same drawing.
- Test the three conditions. Check closed, in-transit and parked states against the same circulation route.
- Confirm the overhead route.
- Review the finish interface.
- Record open questions. Note pass-door needs, signage, and any accessibility requirement that the local authority or client must define.
Drawing Checklist for the Design Team
| Item | What to show | Who confirms |
|---|---|---|
| Pocket mouth | Clear opening at the corridor end, with the nosing line marked | Architect with contractor |
| Parked stack | Occupied footprint at the planned stacking position | Project team with supplier input |
| Overhead route | Continuous connected track path from opening to pocket | Structural and ceiling coordination |
| Pass door | Whether a pass door is required and where it sits | Owner and design team |
| Accessibility | Applicable local clear-width requirement | Local authority or appointed adviser |
Use this table as a meeting record. A tick means the item has been drawn and reviewed, not that a performance outcome has been proven.
Finishes, Seals and Acoustic Expectations at the Junction
Finish selection affects how the pocket edge looks and how it is maintained. Confirm approved surfaces against the actual junction detail, because a corridor nosing is a high-wear line and a finish that suits a wall face may not suit a pocket mouth.
Acoustic concepts can be discussed generically. Seals and perimeter detailing influence how a system performs, but no acoustic outcome should be assumed from a drawing or a finish sample. Ask for project-specific acoustic review where sound separation matters.
Where Evidence Stops and Project Review Begins
Public product information supports the movement principle, the clear-floor concept and the range of finish options. Treat any figure that appears in a tender document as project-specific until its source is confirmed.
For a coordinated review, share the layout, the corridor section and the intended parking position with the supplier early. The movable wall product overview explains the operating principle, and the planning resources support drawing-stage conversations. Pass-door requirements and project documentation can be discussed directly with the team.
Frequently Asked Questions
Does a movable wall need a floor track at the corridor nosing?
No. EBUNGE panels are top-hung and cross the opening without a floor track, so the floor stays clear along the partition line. The nosing remains a finished floor edge and a circulation detail, not a running track.
Can the pocket be placed anywhere along the corridor?
Parking style is customized to the layout and project requirements.
What clear width should we allow at the pocket mouth?
There is no universal figure in this guidance. The required width depends on the applicable local accessibility rule, the corridor use and the parked stack footprint. Confirm it with the responsible design team and authority.
Do finishes affect the clear width check?
Finish thickness and edge detailing can change the visible pocket mouth. Confirm laminate, melamine, fabric, leather, glass or other approved surfaces against the junction detail before the opening is fixed.
Can you confirm acoustic performance for this junction?
Visible references can support layout discussion but do not verify hidden construction or performance.
Is a pass door possible in the partition?
Pass-door requirements can be discussed as part of project documentation. Raise the need early so the door position and the pocket route are reviewed together.
Conclusion
A stacking pocket corridor nosing clear width check is a discipline of drawing the junction three times: closed, in transit and parked. Keep the overhead route continuous, keep the parked stack visible on plan, and keep performance claims tied to project evidence. Confirm support, acoustic and dimensional requirements with the responsible team before construction.
Ready to review your layout? Contact EBUNGE with your drawings and circulation requirements so the pocket, nosing and route can be examined together.


